SATO TG312 Instruction Manual Page 40
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Configuration and Operation
Page 3-10 TG3 Series Operator Manual
3.4 ADJUSTMENT SCREEN
The printer has a quick access to the Adjustment screen for setting the print position, stop position and the
print darkness. These adjustments are in conjunction with the configuration adjustments done in the Service
mode menu and the User mode menu.
1. When the printer is Offline, pressing both the FUNCTION and arrow buttons at the same time will switch
the printer to Adjustment mode. The PITCH POSITION screen is displayed.
2. Press / arrow buttons to set the desired value and press FEED button to save the setting and proceed
to the next Adjustment screen.
3. After adjustment, press ONLINE button or FUNCTION button to exit the Adjustment screen and returns to
Offline mode.
Pressing the ONLINE button or FUNCTION button before pressing the FEED button will not save the
adjustment.
You may wish to print a test print after completing the adjustments to ensure they are correct. Refer to
Section 3.12 Test Print Mode for details.
Menu Description
Adjusts the print position or reference point where the printings begins verti-
cally, relative to the leading edge of each media.
Setting value is adjustable by 0.25mm regardless of print resolution.
Setting range is ±3.75mm and the initial value is +0.00mm.
Adjust the stop (cut) position of each media after printing.
Setting value is adjustable by 0.25mm regardless of print resolution.
Setting range is ±3.75mm and the initial value is +0.00mm.
Adjust the print darkness of the print-out.
Setting range is between 00 and 99, and the initial value is 50.
Note:
It is not advisable to set the print darkness to the higher position as a darker
print-out requires the print head to operate in a higher temperature. Operat-
ing in high temperature may damage the print head in a long run.
Offline mode
Offline mode
Press ONLINE button or
FUNCTION button
Press FUNCTION
+ buttons
FEED
button
FEED
button
FEED
button
* Press or button to set the value.
- Operator Manual 1
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- TABLE OF CONTENTS 6
- Troubleshooting 5 - 1 7
- Basic Specifications 6 - 1 7
- Appendix 8 - 1 8
- Sato Group of Companies 9 - 1 8
- INTRODUCTION 9
- 1.1 FEATURES OF THE PRINTER 10
- 1.2 UNPACKING 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- INSTALLATION 15
- 2.1 SITE LOCATION 16
- 2.2 MEDIA SELECTION 16
- 2.3 LOADING MEDIA 17
- 2.3 LOADING MEDIA (cont’d) 18
- 2.4 MEDIA TYPE SELECTION 20
- 2.5 CUTTER SENSOR ADJUSTMENT 21
- 2.6 LOADING THE CARBON RIBBON 22
- 2.7 REMOVE THE CARBON RIBBON 24
- 2.8 BASIC CONNECTIONS 25
- terminal on 27
- 2.9 LCD POWER SAVING MODE 29
- Section 2: Installation 30
- OPERATION AND CONFIGURATION 31
- FUNCTION 32
- 3.1 OPERATOR PANEL (Cont’d) 33
- 3.2 OPERATING MODES 35
- 3.2 OPERATING MODES (Cont’d) 36
- 3.3 ONLINE AND OFFLINE MODES 38
- Offline mode 40
- 3.6 USER MODE 42
- 3.6 USER MODE (Cont’d) 43
- 3.7 INTERFACE MODE 44
- 3.7 INTERFACE MODE (Cont’d) 45
- 3.8 SEMBL MODE 54
- 3.9 ADVANCED MODE 55
- 3.9 ADVANCED MODE (Cont’d) 56
- 3.10 HEX DUMP MODE 60
- 3.11 RFID USER MODE 61
- 3.11 RFID USER MODE (Cont’d) 62
- 3.12 TEST PRINT MODE 65
- 3.12 TEST PRINT MODE (Cont’d) 66
- 3.13 DEFAULT SETTING MODE 68
- Default value 69
- TG308 TG312 69
- Service Mode 71
- RFID Mode 71
- 3.15 SERVICE MODE 72
- 3.15 SERVICE MODE (Cont’d) 73
- 3.16 RFID MODE 80
- 3.16 RFID MODE (Cont’d) 81
- Indication of 82
- Deletion 82
- 3.17 DOWNLOAD MODE (Cont’d) 83
- CLEANING AND MAINTENANCE 85
- Cleaning sheet 87
- 4.4 ADJUSTING PRINT QUALITY 88
- TROUBLESHOOTING 89
- 5.1.1 Error Message 90
- Command information in 94
- 5.1.3 Warning Message 95
- TROUBLESHOOTING TABLE 96
- PARALLEL INTERFACE 98
- RS232 SERIAL INTERFACE 98
- LAN ETHERNET INTERFACE 99
- WIRELESS LAN INTERFACE 99
- Section 5: Troubleshooting 100
- BASIC SPECIFICATIONS 101
- PROCESSING 102
- PRINTER LANGUAGE 102
- CHARACTER FONT CAPABILITIES 103
- HARDWARE AND RELATED 106
- REGULATORY COMPLIANCE 106
- VERSATILE FUNCTIONS 106
- INTERFACE SPECIFICATIONS 111
- 7.2.2 Basic Specifications 113
- 7.2.3 Ready/Busy 114
- 7.2.4 X-ON/X-OFF 115
- 7.3.1 Basic Specifications 116
- 7.3.2 Pin Assignments 117
- TG3 Series Operator Manual 118
- 7.4.1 Basic Specifications 119
- 7.4.2 Pin Assignments 119
- 7.5.1 Basic Specifications 120
- 7.6 WIRELESS LAN ETHERNET 122
- <Important> 123
- 7.7.5 TELNET Specifications 126
- 7.7.6 Setting/Displayed Items 127
- 7.7.7 Wireless LAN Setting 128
- 7.8.1 Basic Specifications 129
- 7.8.2 Pin Assignments 129
- Page 7-20 130
- APPENDIX 131
- 8.1.1 Parts of Stacker Unit 132
- 8.1.2 To install the Stacker 133
- Metal clamp 134
- First spindle 134
- Section 8: Appendix 135
- Page 8-5 135
- 8.5 BASE REFERENCE POINT 136
- +/-99dot for each media 137
- Item Default value 139
- With cutting motion 141
- 8.7 JUMP HOLE 142
- 8.8 TAG SORTING METHOD 143
- 8.8.2 Separator 144
- Important: 144
- 8.9 PAPER END 145
- Masking 146
- 8.10 RIBBON END 147
- 8.11 RIBBON NEAR END 147
- 8.12 MEDIA SIZE CHECK 147
- 8.13 PERFORATED LINE 148
- Cut prohibited zone 149
- (1mm, 0.04”) 149
- Perforated line 149
- Page 8-20 150
- Page 9-1 151
- SATO GROUP OF COMPANIES 152
Related products and manuals for Label printers SATO TG312
Label printers SATO M-84PRO Specifications
(82 pages)
(82 pages)
Label printers SATO RFID User Manual
(26 pages)
(26 pages)
Label printers SATO CL608VA Specifications
(212 pages)
(212 pages)
(86 pages)
Label printers SATO CG208 Instruction Manual
(110 pages)
(110 pages)
Label printers SATO M60 User Manual
(5 pages)
© 2020, manymanuals.com. All rights reserved. | 1.370 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals