SATO CL612 User Manual download pdf

11213033 Rev B Page 1 of 5

QCOLVC004-SV Interface Cable Rev. B for Sato 8400, 8450,

CL608 / CL408 / CL612 / CL412

CL608E / CL408E / CL612E / CL412E

Description and Installation Instructions

The enclosed cable, that includes an external power supply, connects a Hand Held

Products SV Series verifier to the Sato printer. A mounting stand is also required for the

SV unit. Hand Held Products offers two types of mounting stands or the application may

require a custom stand. A mounting stand is supplied separately from this kit.

Some knowledge of Hand Held Products ScanView software for SV Series setup is

highly recommended for installing and operating this system.

Note:

1. If the SATO printer has a re-winder, the re-winder will require a separate power

supply module. This power supply, SATO part #11S000120, is available through

SATO Distributors.

2. Must operate with cover open or break off the front plastic cover so laser beam is at

the tear bar. Do not break the static brush, which is located at the front plastic cover

– this will not be covered by warranty.

System Operation Overview

This interface is designed so if the verifier senses a bar code problem, the printer will

pause. In the pause condition, verifier LEDs 1 and/or 2 will be ON. To continue printing,

press and release the verifier RESET button.

Note: In this system, the printer will be

operating in dispense mode. If the verifier or cable is disconnected from the

printer in this mode, the printer will not print.

Installation Procedure

1. Turn off printer power.

2. Install the SV mounting stand. (If it is a Hand Held Products “Sky Hook” it will be

mounted on the left side panel.)

3. Mount the SV unit on the stand at the approximate distance shown on the label

mounted on the side of the unit. This is preliminary for power up. Accurate

adjustment will be performed a few steps later in this procedure.

4. Connect the interface cable between the printer 14-pin I/O connector and the SV I/O

connector.

5. Connect a communication cable between the SV Comm connector and a PC running

ScanView setup software.

6. Connect the included power supply to the verifier interface cable and plug in the

power supply to turn on the SV unit.

7. The laser beam is now visible. For best results the beam must be placed in a

location where the bar codes are stable when moving through the beam.

1 2 3 4 5

Summary of Contents

Page 1 - 11213033 Rev B Page 1 of 5

11213033 Rev B Page 1 of 5 QCOLVC004-SV Interface Cable Rev. B for Sato 8400, 8450, CL608 / CL408 / CL612 / CL412 CL608E / CL408E / CL612E / CL412E

Page 2

Page 2 of 5 11213033 Rev B 8. For “picket fence” (horizontal) oriented bar codes, the recommended beam location is on the tear bar. 9. Place a sam

Page 3 - 11213033 Rev B Page 3 of 5

11213033 Rev B Page 3 of 5 Figure 1b – Bad Reflectance Profile Mode 1 Specification A. I/O operation 1. System will operate in Edge Sync or

Page 4

Page 4 of 5 11213033 Rev B 1. LED1 will turn on if Outputs 1 and 2 go active due to ANSI, contrast, or quiet zone failure 2. LED2 will turn on

Page 5 - 11213033 Rev B Page 5 of 5

11213033 Rev B Page 5 of 5 ~LQ0 This command disables partial decodes to activate output ports. NOTE: In SV firmware versions x238 and lower, ~LQ c

Comments to this Manuals

No comments

SATO CL612 User Manual

Browse online or download User Manual for Print & Scan SATO CL612. QCOLVC004-SV Interface Cable Rev. B for Sato 8400, 8450, CL608

Summary of Contents

Comments to this Manuals

Related products and manuals for Print & Scan SATO CL612