SATO GL408e Service Manual Page 11
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Unit 2: Technical Data
GL408-412e Operator Manual
2-2 PN: 9001163A
PHYSICAL CHARACTERISTICS
Width 10.75 Inches (271 mm)
Height 12.00 Inches (305 mm)
Depth 18.00 Inches (455 mm)
Weight 33 Pounds (15 Kg)
ENVIRONMENTAL
Operating Temperature 41 to 104°F (5° to 40°C)
Storage Temperature -4 to 140°F (-20° to 60°C)
Storage Humidity 15 to 85% RH Non-Condensing
Operating Humidity 15 to 85% RH Non-Condensing
POWER
Input Voltage 100-120/200-240 Volts AC +/- 10%, 50/60 Hertz +/-5%
Consumption Voltage
Maximum: 222 Volts AC, 219 Watts (when print ratio is 50%)
Standby: 22.3 Volts AC, 20.6 Watts
PROCESSING
CPU 32 Bit RISC
Flash ROM 8 Megabytes
Receive Buffer 2.95 Megabytes maximum, 0.95 Megabytes near full
COMMAND
Standard
SATO Barcode Printer Language (SBPL)
Intelligent Command
Non-Standard N/A
INTERFACE MODULES
Enhanced Parallel Port IEEE1284 (EPC compatible)
Serial Port 9-Pin RS232C
Universal Serial Bus (USB) USB Adapter (480 Mbps)
Local Area Network (LAN) 10BASE-T/100BASE-TX Automatic Switching
Ethernet (Wireless LAN) 802.11g Wireless Wi-Fi
PRINT
Method Direct Thermal / Thermal Transfer
Maximum Speed (selectable) 2, 3, 4, 5, 6, 7, 8, 9, 10 Inches Per Second (50.8 - 254 mm)
Print Module (dot size) .0049 Inches (.125 mm)
Resolution
GL408e: 203 Dots Per Inch (8 dpmm)
GL412e: 305 Dots Per Inch (12 dpmm)
Maximum Print Width 4.09 Inches (104 mm)
Maximum Print Length 98.98 Inches (2514 mm)
- GL408/412e 1
- PRINTER 1
- SATO America, Inc 2
- TABLE OF CONTENTS 3
- INTRODUCTION 6
- ABOUT THIS MANUAL 7
- GENERAL DESCRIPTION 8
- CONTROL FEATURES 9
- TECHNICAL DATA 10
- 2-2 PN: 9001163A 11
- REGULATORY 12
- CHARACTER FONT CAPABILITIES 13
- BARCODE CAPABILTIES 14
- INSTALLATION 15
- Accessory Box 16
- Shipping Container 16
- PRINTER INSTALLATION 17
- MEDIA SELECTION 18
- MEDIA & RIBBON LOADING 18
- 3-5 PN: 9001163A 19
- Figure 3-3c, Ribbon Loading 19
- CONTINUOUS MODE 20
- TEAR-OFF MODE 20
- CUTTER MODE 20
- DISPENSE MODE 20
- LINERLESS MODE 20
- LABEL PRINT DIRECTION 21
- INTERFACE SELECTION 22
- READY/BUSY INTERFACE SIGNALS 23
- SIGNAL SIGNAL DEFINITION 23
- READY/BUSY CABLE REQUIREMENTS 23
- IEEE1284 PARALLEL INTERFACE 24
- 1 To Hos t 32 Fault To Host 24
- 1 From Host 24
- UNIVERSAL SERIAL BUS (USB) 25
- 802.11G WIRELESS 26
- WIRELESS LAN SIGNAL STRENGTH 27
- SOFTWARE SPECIFICATIONS 27
- ALL INTERFACES 28
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- EXTERNAL SIGNAL 31
- 25-PIN CONNECTOR ASSIGNMENTS 32
- INPUT SIGNAL WAVE FORM 33
- START PRINTING 33
- REPRINTING 33
- OUTPUT SIGNAL WAVE FORM 34
- BASIC OPERATION 34
- PAPER END 34
- RIBBON END 34
- MACHINE ERROR 34
- 3-21 PN: 9001163A 35
- ACCESSORIES INSTALLATION 36
- CONFIGURATION 37
- PRINTER CONFIGURATION 38
- CONFIGURATION MODES 39
- CONFIGURATION MODE 40
- ADVANCED MODE 41
- 4-6 PN: 9001163A 42
- SERIAL INTERFACE MODE 43
- PARALLEL INTERFACE MODE 44
- CENTRONICS INTERFACE MODE 45
- 4-10 PN: 9001163A 46
- 4-11 PN: 9001163A 47
- 4-12 PN: 9001163A 48
- PGL EMULATION MODE 49
- ZGL EMULATION MODE 50
- DGL EMULATION MODE 51
- TGL EMULATION MODE 52
- IGL EMULATION MODE 53
- DIAGNOSTICS MODE 54
- PRINTER MANAGEMENT MODE 55
- DISPLAY INTENSITY ADJUSTMENT 56
- BUFFER CLEAR 56
- SOFT RESET 57
- KEY LOCK/UNLOCK 57
- USER MODE 58
- USER MODE (TABLE 4-1) 59
- ADVANCED MODE (TABLE 4-3) 65
- Data Protocol 78
- Buffer Size in K 78
- EMULATION 99
- MENU DESCRIPTION 100
- Command* 118
- IGL Setup 118
- Save state* 118
- DIAGNOSTICS 118
- Priority Setting 118
- Error Log Clear 120
- TROUBLESHOOTING 125
- ERROR SIGNAL TROUBLESHOOTING 126
- DISPLAY EXPLANATION SOLUTION 127
- TROUBLESHOOTING TABLE 132
- NO PRINTED IMAGE 133
- INCORRECT LABEL POSITIONING 133
- SMEARED PRINT IMAGES 133
- INTERFACE TROUBLESHOOTING 134
- LAN ETHERNET INTERFACE 135
- 802.11G WIRELESS INTERFACE 135
- CENTRONICS INTERFACE 135
- HEX DUMP 136
- TEST LABEL PRINTING 136
- 5-13 PN: 9001163A 137
- Figure 6-2, Sample Test Label 137
- MAINTENANCE 138
- CLEANING PROCEDURES 139
- PRINT HEAD REPLACEMENT 140
- FUSE REPLACEMENT 141
- Platen Roller Assy 142
- Retaining Bracket 142
- Lower Print Assy 142
- LABEL SENSOR POSITIONING 143
- PRINT HEAD BALANCE ADJUSTMENT 144
- PRINT HEAD PRESSURE 145
- PRINT HEAD ALIGNMENT 146
- RIBBON GUIDE ALIGNMENT 147
- RIBBON ROLLER ALIGNMENT 148
Related products and manuals for Networking SATO GL408e
(35 pages)© 2020, manymanuals.com. All rights reserved. | 0.954 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals