SATO GL408e Service Manual Page 52
- Page / 148
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Unit 4: Printer Configuration
GL408-412e Operator Manual
4-16 PN: 9001163A
TGL EMULATION MODE
This chapter provides the programming sequences required to correlate the printer’s interpreter language with that
of TEC interpretor language. Use the keys of the printer’s operator panel to select and enter the required options.
Refer to the Menu Definition Tables in the following chapter to provide an explanation of each menu screen.
Figure 4-13, TGL Emulation Mode
ATTENTION: Perform the following programming sequence only if this is the
emulation type required. Instead, refer to the appropriate emulation chart.
EMULATION
Active
Yes*
EMULATION
Select
Select
TGL*
POWER
ONLINE
OFFLINE
LINE
FUNCTION
Emulation
Mode
ENTER
TGL Setup
Active
Print Errors
Character Set
Slash Zero
Image Scale
SFCC Select
EURO Symbol
Speed CMDs
AY Intensity CMD
U1/U2 Move CMDs
XS Sensor Param
XS Media ‘C’ Act
XS Media ‘D’ Act
AR Pre-Feed CMD
AX Fine Adj. CMD
Page alignment
Vert. DPI Adjust
Status Response
Print Errors
Disable*
Character Set
PC-850*
Slash Zero
Disable*
Image Scale
Disable*
SFCC Select
Auto Select*
EURO Symbol
0xB0*
Speed CMDs
Process*
AY Intensity CMD
Process*
XS Sensor Param
Process*
XS Media ‘C’ Act
Continuous*
XS Media ‘D’ Act
Tear-Off*
AR Pre-Feed CMD
Process*
AX Fine Adj. CMD
Process*
Page alignment
Center*
Vert. DPI Adjust
0*
Status Response
Disable*
U1/U2 Move CMDs
Process*
- GL408/412e 1
- PRINTER 1
- SATO America, Inc 2
- TABLE OF CONTENTS 3
- INTRODUCTION 6
- ABOUT THIS MANUAL 7
- GENERAL DESCRIPTION 8
- CONTROL FEATURES 9
- TECHNICAL DATA 10
- 2-2 PN: 9001163A 11
- REGULATORY 12
- CHARACTER FONT CAPABILITIES 13
- BARCODE CAPABILTIES 14
- INSTALLATION 15
- Accessory Box 16
- Shipping Container 16
- PRINTER INSTALLATION 17
- MEDIA SELECTION 18
- MEDIA & RIBBON LOADING 18
- 3-5 PN: 9001163A 19
- Figure 3-3c, Ribbon Loading 19
- CONTINUOUS MODE 20
- TEAR-OFF MODE 20
- CUTTER MODE 20
- DISPENSE MODE 20
- LINERLESS MODE 20
- LABEL PRINT DIRECTION 21
- INTERFACE SELECTION 22
- READY/BUSY INTERFACE SIGNALS 23
- SIGNAL SIGNAL DEFINITION 23
- READY/BUSY CABLE REQUIREMENTS 23
- IEEE1284 PARALLEL INTERFACE 24
- 1 To Hos t 32 Fault To Host 24
- 1 From Host 24
- UNIVERSAL SERIAL BUS (USB) 25
- 802.11G WIRELESS 26
- WIRELESS LAN SIGNAL STRENGTH 27
- SOFTWARE SPECIFICATIONS 27
- ALL INTERFACES 28
- STATUS5 TIMING CHARTS 29
- NORMAL PROCESS 29
- CANCEL PROCESS 29
- ERROR PROCESS 29
- PRINT PROCESS 30
- COMMAND PROCESS 30
- BCC ERROR PROCESS 30
- EXTERNAL SIGNAL 31
- 25-PIN CONNECTOR ASSIGNMENTS 32
- INPUT SIGNAL WAVE FORM 33
- START PRINTING 33
- REPRINTING 33
- OUTPUT SIGNAL WAVE FORM 34
- BASIC OPERATION 34
- PAPER END 34
- RIBBON END 34
- MACHINE ERROR 34
- 3-21 PN: 9001163A 35
- ACCESSORIES INSTALLATION 36
- CONFIGURATION 37
- PRINTER CONFIGURATION 38
- CONFIGURATION MODES 39
- CONFIGURATION MODE 40
- ADVANCED MODE 41
- 4-6 PN: 9001163A 42
- SERIAL INTERFACE MODE 43
- PARALLEL INTERFACE MODE 44
- CENTRONICS INTERFACE MODE 45
- 4-10 PN: 9001163A 46
- 4-11 PN: 9001163A 47
- 4-12 PN: 9001163A 48
- PGL EMULATION MODE 49
- ZGL EMULATION MODE 50
- DGL EMULATION MODE 51
- TGL EMULATION MODE 52
- IGL EMULATION MODE 53
- DIAGNOSTICS MODE 54
- PRINTER MANAGEMENT MODE 55
- DISPLAY INTENSITY ADJUSTMENT 56
- BUFFER CLEAR 56
- SOFT RESET 57
- KEY LOCK/UNLOCK 57
- USER MODE 58
- USER MODE (TABLE 4-1) 59
- ADVANCED MODE (TABLE 4-3) 65
- Data Protocol 78
- Buffer Size in K 78
- EMULATION 99
- MENU DESCRIPTION 100
- Command* 118
- IGL Setup 118
- Save state* 118
- DIAGNOSTICS 118
- Priority Setting 118
- Error Log Clear 120
- TROUBLESHOOTING 125
- ERROR SIGNAL TROUBLESHOOTING 126
- DISPLAY EXPLANATION SOLUTION 127
- TROUBLESHOOTING TABLE 132
- NO PRINTED IMAGE 133
- INCORRECT LABEL POSITIONING 133
- SMEARED PRINT IMAGES 133
- INTERFACE TROUBLESHOOTING 134
- LAN ETHERNET INTERFACE 135
- 802.11G WIRELESS INTERFACE 135
- CENTRONICS INTERFACE 135
- HEX DUMP 136
- TEST LABEL PRINTING 136
- 5-13 PN: 9001163A 137
- Figure 6-2, Sample Test Label 137
- MAINTENANCE 138
- CLEANING PROCEDURES 139
- PRINT HEAD REPLACEMENT 140
- FUSE REPLACEMENT 141
- Platen Roller Assy 142
- Retaining Bracket 142
- Lower Print Assy 142
- LABEL SENSOR POSITIONING 143
- PRINT HEAD BALANCE ADJUSTMENT 144
- PRINT HEAD PRESSURE 145
- PRINT HEAD ALIGNMENT 146
- RIBBON GUIDE ALIGNMENT 147
- RIBBON ROLLER ALIGNMENT 148
Related products and manuals for Networking SATO GL408e
(35 pages)© 2020, manymanuals.com. All rights reserved. | 2.850 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals