SATO CG4 Series Instruction Manual Page 41
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 3: Operation and Configuration
CG4 Series Operator Manual Page 3-13
3.5
OPERATION SETTING MODE
(cont’d)
Notes:
•Press the FEED/LINE button to select the desired function, and then execute the selected function by
pressing and holding the FEED/LINE button for more than 3 seconds.
• When the desired interface is selected, this setting will be valid after you restart the printer.
• When HEX dump mode is selected, the printer will be set to this mode only once by restarting the printer.
• When download mode is selected, the printer will be reset automatically and it enters the desired
download mode.
• When the default setting mode is selected and executed, the printer will be set to default setting.
• Make sure that the function execution is complete (ON LINE (POWER) indicator: Green light) before
turning off the printer.
3.6 PROGRAM DOWNLOAD MODE
In this mode, the printer is set to receive an application program from the host computer to download into its
memory. Remember to set the printer to the correct active interface to be used for the data transfer.
Status of printer in Program Download Mode
ON LINE (POWER)
indicator
ERROR
indicator
Buzzer
Activation via operation
setting mode or
download command.
Start-up
Reception
from interface?
Yes
Reboot
command
reception?
Program data
reception?
Yes
Yes
No
No
No
Download
Download
completion
Reboot and start in normal mode
Test print
Online
At the start of download
mode
Wait to receive data
Start receiving data/
Receiving data
Writing to flash ROM
At the time of download
completion
Printer turns off
Printer turns on again
Test printing
(From step 4 of Operation Setting Mode. )
One long
beep
One
short
beep
One
short
beep
One short
beep
Red light
(after
release of
FEED/LINE)
Off
(after release of
FEED/LINE)
Blinking red lightOff
Off
(while pressing
FEED/LINE)
Off
(while pressing
FEED/LINE)
Blinking green light
Off
Three
long
beeps
Blinking green light
Off
Blinking green light
(lights alternately)
Blinking red light
(lights alternately)
Green light
Off
Off
Off
Off
Red light
Green light
Off
Green light
Off
- Operator Manual 1
- SATO America, Inc 2
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- Table of Contents 7
- INTRODUCTION 9
- 1.2.1 Included Accessories 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- Section 1: Introduction 14
- INSTALLATION 15
- 2.2 MEDIA SELECTION 16
- 2.1 SITE LOCATION 16
- 2.3 LOADING LABELS 17
- 2.3 LOADING LABELS (cont’d) 18
- Roll media (Face-in) 20
- Roll media (Face-out) 20
- Fan-fold media 20
- (Printed side face up) 20
- Ribbon unit 21
- Ribbon route 23
- 2.5 CONNECTIONS 24
- 2.5 CONNECTIONS (cont’d) 27
- 2.5.5 Turning On the Power 27
- 2.5.6 Turning Off the Power 27
- Section 2: Installation 28
- OPERATION AND CONFIGURATION 29
- 3.1 OPERATOR PANEL 30
- 3.2 OPERATING MODES 31
- 3.3 USER TEST PRINT MODE 32
- Offset value (Vertical and 33
- Pitch offset value ±099 DOT 33
- 3.4 FACTORY TEST PRINT MODE 36
- Base reference correction 38
- 3.5 OPERATION SETTING MODE 39
- OPERATION SETTING MODE 40
- 3.6 PROGRAM DOWNLOAD MODE 41
- 3.6.1 Firmware Download 42
- 3.7 FONT DOWNLOAD MODE 43
- 3.8 DEFAULT SETTING MODE 44
- 3.9 HEX DUMP MODE 45
- TROUBLESHOOTING 49
- Incorrect 50
- Download 50
- TROUBLESHOOTING TABLE 52
- LIGHT PRINT IMAGES 53
- UNEVEN PRINT DARKNESS 53
- SMEARED PRINT IMAGES 53
- MEANDERING MEDIA 53
- CHK TROUBLESHOOTING STEP 54
- 4.4.1 Hex Dump 55
- 4.4.2 Test label printing 55
- Section 4: Troubleshooting 56
- CLEANING AND MAINTENANCE 57
- I-Mark and Gap 59
- Media guide 59
- 5.4 EASY REPLACEMENT OF PARTS 60
- Fulcrum shaft 62
- Circular 62
- 5.5 ADJUSTING PRINT QUALITY 63
- GENERAL SPECIFICATIONS 65
- PHYSICAL CHARACTERISTICS 65
- POWER SUPPLY (AC ADAPTER) 65
- MODEL NAME 66
- BARCODE CAPABILITIES 69
- STANDARD FUNCTIONS 69
- HARDWARE AND RELATED 70
- REGULATORY COMPLIANCE 70
- CUTTER SPECIFICATIONS 71
- DISPENSER SPECIFICATIONS 71
- INTERFACE SPECIFICATIONS 73
- 7.2 RS232C SERIAL INTERFACE 74
- 7.2.2 Ready/Busy 76
- 7.2.3 X-ON/X-OFF 77
- 7.3.2 Pin Assignments 79
- 7.3.3 Input/Output Signals 80
- 7.4.2 Pin Assignments 81
- 7.4.3 Host Computer Settings 82
- 7.5.2 Software Specifications 84
- 7.5.3 TCP/IP Specifications 85
- 7.5.4 LPD Specifications 85
- 7.5.5 FTP Specifications 85
- 7.5.6 TELNET Specifications 86
- 7.5.7 Setting/Displayed Items 86
- APPENDIX 89
- 8.1.2 Cut position Adjustment 90
- Label output 92
- 8.4 OPERATION MODE SELECTION 94
- Continuous Mode 95
- Tear off Mode 95
- Cutter Mode 95
- Dispenser Mode 96
- Linerless (Non Sepa) Mode 96
- Base reference 97
- 8.7 PAPER END 98
- Feeds 50mm 99
- 8.7.2 Fanfold Label End 99
- Section 8: Appendix 100
- SATO GROUP OF COMPANIES 101
Related products and manuals for Print & Scan SATO CG4 Series
Print & Scan SATO XL4xxe User Manual
(114 pages)
(114 pages)
Print & Scan SATO CL608 Specifications
(12 pages)
(12 pages)
Print & Scan SATO /gt Series User Manual
(27 pages)
(27 pages)
Print & Scan SATO TH208 Instruction Manual
(20 pages)
(20 pages)
Print & Scan SATO CT4i Series Service Manual
(74 pages)
(74 pages)
Print & Scan SATO GY412 Instruction Manual
(217 pages)
(217 pages)
Print & Scan SATO XL400 User Manual
(194 pages)
(194 pages)
Print & Scan SATO M8485Se Service Manual
(216 pages)
(216 pages)
Print & Scan SATO CG412TT User Manual
(102 pages)
(102 pages)
Print & Scan SATO XL4xxe User Manual
(121 pages)
(121 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
Print & Scan SATO TXPSX5 User Manual
(1 pages)
(1 pages)
Print & Scan SATO M8450 User Manual
(60 pages)
(60 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
© 2020, manymanuals.com. All rights reserved. | 0.335 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals