SATO CG4 Series Instruction Manual Page 95
- Page / 102
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 8: Appendix
CG4 Series Operator Manual Page 8-7
8.5 BASE REFERENCE POINT
The base reference point is the point at which one determines the print and cut positions.
The base reference position differs, depending on the print mode or the label pitch sensor to be used.
I-Mark I-Mark (CX-compatible)
Gap
Base print
position
Base print
position
I-Mark I-Mark (CX-compatible)
Gap
Continuous Mode
Gap end
(Base print
position)
Gap start
• The start of I-Mark is the base print position when using the I-Mark sensor.
• The end of I-Mark is the base print position when using the I-Mark (CX-compatible) sensor.
• The end of label Gap is the base print position when using the label Gap sensor.
• The center of label gap is the base tear off position when using the I-Mark sensor.*
• The center of label gap is the base tear off position when using the I-Mark (CX-compatible) sensor.*
• The center of label gap is the base tear off position when using the label Gap sensor.*
• The center of label gap is the base cut position when using the I-Mark sensor.*
• The center of label gap is the base cut position when using the I-Mark (CX-compatible) sensor.
• The center of label gap is the base cut position when using the label Gap sensor.*
* Default value of label gap saved in the printer is 3mm (0.12”). Therefore, the distance from the base print position
to the center of label gap is 1.5mm (0.06”) (Default value). When the size of label gap is not 3mm (0.12”), use the
he <PC> command or the <PG> command to set the gap size properly. For the command details, refer to the
Command Reference.
Base print
position
Base tear off
position
Base print
position
Base tear off
position
Base print
position
Base tear off
position
Tear off Mode
I-Mark I-Mark (CX-compatible)
Gap
Cutter Mode
Center of
label gap
Center of
label gap
Center of
label gap
Center of
label gap
Base print
position
Base cut
position
Base print
position
Base cut
position
Base print
position
Base cut
position
- Operator Manual 1
- SATO America, Inc 2
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- Table of Contents 7
- INTRODUCTION 9
- 1.2.1 Included Accessories 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- Section 1: Introduction 14
- INSTALLATION 15
- 2.2 MEDIA SELECTION 16
- 2.1 SITE LOCATION 16
- 2.3 LOADING LABELS 17
- 2.3 LOADING LABELS (cont’d) 18
- Roll media (Face-in) 20
- Roll media (Face-out) 20
- Fan-fold media 20
- (Printed side face up) 20
- Ribbon unit 21
- Ribbon route 23
- 2.5 CONNECTIONS 24
- 2.5 CONNECTIONS (cont’d) 27
- 2.5.5 Turning On the Power 27
- 2.5.6 Turning Off the Power 27
- Section 2: Installation 28
- OPERATION AND CONFIGURATION 29
- 3.1 OPERATOR PANEL 30
- 3.2 OPERATING MODES 31
- 3.3 USER TEST PRINT MODE 32
- Offset value (Vertical and 33
- Pitch offset value ±099 DOT 33
- 3.4 FACTORY TEST PRINT MODE 36
- Base reference correction 38
- 3.5 OPERATION SETTING MODE 39
- OPERATION SETTING MODE 40
- 3.6 PROGRAM DOWNLOAD MODE 41
- 3.6.1 Firmware Download 42
- 3.7 FONT DOWNLOAD MODE 43
- 3.8 DEFAULT SETTING MODE 44
- 3.9 HEX DUMP MODE 45
- TROUBLESHOOTING 49
- Incorrect 50
- Download 50
- TROUBLESHOOTING TABLE 52
- LIGHT PRINT IMAGES 53
- UNEVEN PRINT DARKNESS 53
- SMEARED PRINT IMAGES 53
- MEANDERING MEDIA 53
- CHK TROUBLESHOOTING STEP 54
- 4.4.1 Hex Dump 55
- 4.4.2 Test label printing 55
- Section 4: Troubleshooting 56
- CLEANING AND MAINTENANCE 57
- I-Mark and Gap 59
- Media guide 59
- 5.4 EASY REPLACEMENT OF PARTS 60
- Fulcrum shaft 62
- Circular 62
- 5.5 ADJUSTING PRINT QUALITY 63
- GENERAL SPECIFICATIONS 65
- PHYSICAL CHARACTERISTICS 65
- POWER SUPPLY (AC ADAPTER) 65
- MODEL NAME 66
- BARCODE CAPABILITIES 69
- STANDARD FUNCTIONS 69
- HARDWARE AND RELATED 70
- REGULATORY COMPLIANCE 70
- CUTTER SPECIFICATIONS 71
- DISPENSER SPECIFICATIONS 71
- INTERFACE SPECIFICATIONS 73
- 7.2 RS232C SERIAL INTERFACE 74
- 7.2.2 Ready/Busy 76
- 7.2.3 X-ON/X-OFF 77
- 7.3.2 Pin Assignments 79
- 7.3.3 Input/Output Signals 80
- 7.4.2 Pin Assignments 81
- 7.4.3 Host Computer Settings 82
- 7.5.2 Software Specifications 84
- 7.5.3 TCP/IP Specifications 85
- 7.5.4 LPD Specifications 85
- 7.5.5 FTP Specifications 85
- 7.5.6 TELNET Specifications 86
- 7.5.7 Setting/Displayed Items 86
- APPENDIX 89
- 8.1.2 Cut position Adjustment 90
- Label output 92
- 8.4 OPERATION MODE SELECTION 94
- Continuous Mode 95
- Tear off Mode 95
- Cutter Mode 95
- Dispenser Mode 96
- Linerless (Non Sepa) Mode 96
- Base reference 97
- 8.7 PAPER END 98
- Feeds 50mm 99
- 8.7.2 Fanfold Label End 99
- Section 8: Appendix 100
- SATO GROUP OF COMPANIES 101
Related products and manuals for Print & Scan SATO CG4 Series
Print & Scan SATO XL4xxe User Manual
(114 pages)
(114 pages)
Print & Scan SATO CL608 Specifications
(12 pages)
(12 pages)
Print & Scan SATO /gt Series User Manual
(27 pages)
(27 pages)
Print & Scan SATO TH208 Instruction Manual
(20 pages)
(20 pages)
Print & Scan SATO CT4i Series Service Manual
(74 pages)
(74 pages)
Print & Scan SATO GY412 Instruction Manual
(217 pages)
(217 pages)
Print & Scan SATO XL400 User Manual
(194 pages)
(194 pages)
Print & Scan SATO M8485Se Service Manual
(216 pages)
(216 pages)
Print & Scan SATO CG412TT User Manual
(102 pages)
(102 pages)
Print & Scan SATO XL4xxe User Manual
(121 pages)
(121 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
Print & Scan SATO TXPSX5 User Manual
(1 pages)
(1 pages)
Print & Scan SATO M8450 User Manual
(60 pages)
(60 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
Print & Scan SATO MB200/201i User Manual
(73 pages)
(73 pages)
© 2020, manymanuals.com. All rights reserved. | 0.124 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals