SATO TH208 Instruction Manual Page 106
- Page / 160
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 4: Cleaning and Maintenance
Page 4-4 TH2 Series Operator Manual
4.4 EASY REPLACEMENT OF PARTS
It is easy to replace the print head of the TH2 Series printer.
The tool-less print head release mechanism enables the print head to be quickly and easily replaced.
4.4.1 Releasing and Replacing the Print Head
The print head on the printer is a user-replaceable item. If it becomes damaged for any reason, it can be
easily removed and replaced. Contact your local SATO representative for information on obtaining a new print
head.
1. Make sure the printer is turned off, and disconnect the
power cable. If the optional battery pack is installed, remove
it as well.
2. Lift the Top Cover.
3. Press and release the side tab (see arrow ) on both
sides of the dispensing sensor cover. Remove the cover
and set it aside.
4. Press and push up the print head assembly to release it
from the catches.
5. The cable connector (circled) at the rear of the print head
assembly is now exposed. Gently disconnect the print
head from the cable connector.
6. Carefully attach a replacement print head assembly to the
cable connector. The connector is keyed so that it can only
be inserted in the correct orientation.
Caution:
While handling the print head, be careful not to scratch the
printing surface of the print head. Scratching the surface
will cause permanent and irreparable damage that is not
covered by the warranty!
7. Reinsert the new print head assembly into the printer,
making sure that the hooks at the back of the print head
assembly fit on the catches of the printer.
8. Fix the dispensing sensor cover back to its position and
push lightly until it locks with a click sound.
9. Close the Top Cover.
10.Restore power, reload media, reset the head counter and
perform a test print to ensure that the print head is
connected properly.
Dispensing
sensor
cover
1
2
1
1
Print head
assembly
catches
Print head
assembly
Print head
assembly
- Operator Manual 1
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- TABLE OF CONTENTS 6
- INTRODUCTION 9
- 1.1 FEATURES OF THE PRINTER 10
- 1.2 UNPACKING 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 13
- INSTALLATION 15
- 2.1 SITE LOCATION 16
- 2.2 MEDIA SELECTION 16
- 2.3 LOADING MEDIA 17
- Media guides 18
- 2.4 CONNECTIONS 21
- 2.4 CONNECTIONS (cont’d) 23
- 2.4.4 Turning On the Power 23
- 2.4.5 Turning Off the Power 23
- DC input 25
- AC adapter 25
- Battery pack 25
- Terminal side 25
- OPERATION AND CONFIGURATION 27
- 3.1 OPERATOR PANEL 28
- 3.1 OPERATOR PANEL (Cont’d) 29
- 3.2 OPERATING MODES 34
- 3.2 OPERATING MODES (Cont’d) 35
- 3.3 PRINT MENU 36
- 3.3 PRINT MENU (Cont’d) 37
- 3.4 MAIN MENU 40
- 3.5 SETTINGS MENU 40
- 3.6 APPLICATION MENU 41
- 3.6 APPLICATION MENU (Cont’d) 42
- 3.6.2 To edit the FIELD menu 44
- 1.truetype 55
- 2.bitmap 55
- 3.6.12 To edit the F1 menu 64
- 3.7 PRINTER SETUP MENU 66
- To be continued on the 73
- Continued from the 74
- and its unit 78
- TEST LABELS - Pattern 84
- TEST LABELS - Factory 84
- 3.8 ADVANCED SETUP MENU 96
- 3.9 F1 SHORTCUTS MENU 100
- CLEANING AND MAINTENANCE 103
- I-Mark and 104
- Gap sensor 104
- Dispensing sensor 105
- 4.4 EASY REPLACEMENT OF PARTS 106
- Gear cover 107
- Screws x 2 107
- Dispensing 107
- TROUBLESHOOTING 109
- 5.1.2 Error Message 110
- Section 5: Troubleshooting 111
- TROUBLESHOOTING TABLE 113
- LAN ETHERNET INTERFACE 115
- WIRELESS LAN INTERFACE 115
- 5.4.1 Hex Dump 116
- 5.4.2 Test label printing 116
- BASIC SPECIFICATIONS 117
- CHARACTER FONT CAPABILITIES 119
- REGULATORY COMPLIANCE 121
- CUTTER KIT SPECIFICATIONS 122
- BATTERY SPECIFICATIONS 122
- INTERFACE SPECIFICATIONS 125
- 7.2.2 Pin Assignments 126
- 7.3.3 Software Specifications 129
- 7.3.4 TCP/IP Specifications 129
- 7.3.5 Setting/Displayed Items 130
- 7.3.6 Wireless LAN Setting 130
- APPENDIX 135
- Figure 1 136
- Cut prohibited zone 136
- (1mm, 0.04”) 136
- Perforated line 136
- 8.1.3 Cutter replacement 137
- 8.3 OPERATION MODE SELECTION 138
- 8.3.2 Tear Off Mode 139
- 8.3.3 Dispensing Mode 140
- 8.3.4 Cutter Mode 142
- 8.3.4 Cutter Mode (cont’d) 143
- 8.3.5 Linerless Cutter Mode 144
- 8.3.6 Journal Mode 145
- 8.3.7 Tear Off Journal Mode 146
- 8.4.8 Cutter Journal Mode 147
- 8.4 BASE REFERENCE POINT 150
- 8.5 ADJUSTMENTS 151
- Section 8: Appendix 152
- LICENSE AGREEMENTS 153
- SATO fonts: 155
- LuaSocket 2.0.2 license: 156
- Bitlib: 157
- BSD (strftime): 157
- Section 8: License Agreements 158
- SATO GROUP OF COMPANIES 159
Related products and manuals for Print & Scan SATO TH208
Print & Scan SATO CG212DT Instruction Manual
(38 pages)
(38 pages)
Print & Scan SATO CT410 Specifications
(8 pages)
(8 pages)
Print & Scan SATO M-8400 Specifications
(12 pages)
(12 pages)
Print & Scan SATO XL4xxe User Manual
(13 pages)
(13 pages)
Print & Scan SATO GY412 Instruction Manual
(24 pages)
(24 pages)
Print & Scan SATO XL400 Specifications
(80 pages)
(80 pages)
Print & Scan SATO D512 User Manual
(88 pages)
(88 pages)
Print & Scan SATO SX4M Owner's Manual
(18 pages)
(18 pages)
Print & Scan SATO DR300 Specifications
(60 pages)
(60 pages)
Print & Scan SATO GT412 Instruction Manual
(102 pages)
(102 pages)
Print & Scan SATO D508 User Manual
(28 pages)
(28 pages)
Print & Scan SATO CL4NX User Manual
(62 pages)
(62 pages)
Print & Scan SATO CX212 Specifications
(116 pages)
(116 pages)
Print & Scan SATO CL408e/412e User Manual
(16 pages)
Print & Scan SATO CX200 User's Guide
(7 pages)
(7 pages)
Print & Scan SATO MB200i Specifications
(10 pages)
(10 pages)
Print & Scan SATO /gt Series Specifications
(152 pages)
(152 pages)
Print & Scan SATO CG4 Series User Manual
(102 pages)
(102 pages)
Print & Scan SATO CG412TT User Manual
(104 pages)
(104 pages)
© 2020, manymanuals.com. All rights reserved. | 1.505 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals