SATO TG312 Instruction Manual Page 134
- Page / 152
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
Section 8: Appendix
Page 8-4
TG3 Series Operator Manual
8.2 OPTIONAL ACCESSORIES - LABEL REWINDER
The rewinder is an external unit that allows for labels to be rewound in rolls up to 107mm (4.2”) in diameter. The
rewinder derives its power using a built-in cable connected directly to the printer’s
EXT connector. The
rewinder facilitates the rewinding of labels from the printer and subsequently unwinds the media for use with
applicators.
8.2.1 To install the Label Rewinder
1. Slot in the Alignment plate to the base of the rewinder.
2. Position the Label rewinder with the alignment plate
attached, to the front of the printer and slot the other end of
alignment plate to the base of printer.
(The Rewind spindle
of the rewinder should be positioned away from the printer.)
3. Connect the built-in cable from the Rewinder to the EXT
connector at the rear of the printer.
4. On the Rewinder, remove the metal clamp from the Rewind
Spindle.
5. Feed the lead end of the label stock under the first spindle
and onto the Rewind Spindle.
Feed the stock around the spindle once, then replace the
metal clamp over the label stock.
Wind another revolution to ensure the labels are secure on
the spindle.
6. Power on the printer.
8.3 OPTIONAL ACCESSORIES - KEYPAD
The optional keypad can be connected to the TG3 Series printer with the Keypad connection terminal, thus
providing a stand-alone function.
1. Make sure that power cable is not connected to the
printer.
2. Connect the cable from the optional Keypad device to
the
Keypad connection terminal at the left side of the
Media ejection slot of the printer.
Note:
Make sure the connector is correctly oriented. Secure
the printer with one hand, and insert the connector firmly.
3. Set the printer for use with the connected device. Refer
to
Section 3.7 Interface Mode and perform the
procedures to set the
Keypad CONNECT to ENABLE.
Metal clamp
First spindle
Label
stock
- Operator Manual 1
- Safety Precautions 3
- Select a Safe Location 5
- Power Supply 5
- TABLE OF CONTENTS 6
- Troubleshooting 5 - 1 7
- Basic Specifications 6 - 1 7
- Appendix 8 - 1 8
- Sato Group of Companies 9 - 1 8
- INTRODUCTION 9
- 1.1 FEATURES OF THE PRINTER 10
- 1.2 UNPACKING 10
- 1.3 PARTS IDENTIFICATION 11
- Back view 12
- INSTALLATION 15
- 2.1 SITE LOCATION 16
- 2.2 MEDIA SELECTION 16
- 2.3 LOADING MEDIA 17
- 2.3 LOADING MEDIA (cont’d) 18
- 2.4 MEDIA TYPE SELECTION 20
- 2.5 CUTTER SENSOR ADJUSTMENT 21
- 2.6 LOADING THE CARBON RIBBON 22
- 2.7 REMOVE THE CARBON RIBBON 24
- 2.8 BASIC CONNECTIONS 25
- terminal on 27
- 2.9 LCD POWER SAVING MODE 29
- Section 2: Installation 30
- OPERATION AND CONFIGURATION 31
- FUNCTION 32
- 3.1 OPERATOR PANEL (Cont’d) 33
- 3.2 OPERATING MODES 35
- 3.2 OPERATING MODES (Cont’d) 36
- 3.3 ONLINE AND OFFLINE MODES 38
- Offline mode 40
- 3.6 USER MODE 42
- 3.6 USER MODE (Cont’d) 43
- 3.7 INTERFACE MODE 44
- 3.7 INTERFACE MODE (Cont’d) 45
- 3.8 SEMBL MODE 54
- 3.9 ADVANCED MODE 55
- 3.9 ADVANCED MODE (Cont’d) 56
- 3.10 HEX DUMP MODE 60
- 3.11 RFID USER MODE 61
- 3.11 RFID USER MODE (Cont’d) 62
- 3.12 TEST PRINT MODE 65
- 3.12 TEST PRINT MODE (Cont’d) 66
- 3.13 DEFAULT SETTING MODE 68
- Default value 69
- TG308 TG312 69
- Service Mode 71
- RFID Mode 71
- 3.15 SERVICE MODE 72
- 3.15 SERVICE MODE (Cont’d) 73
- 3.16 RFID MODE 80
- 3.16 RFID MODE (Cont’d) 81
- Indication of 82
- Deletion 82
- 3.17 DOWNLOAD MODE (Cont’d) 83
- CLEANING AND MAINTENANCE 85
- Cleaning sheet 87
- 4.4 ADJUSTING PRINT QUALITY 88
- TROUBLESHOOTING 89
- 5.1.1 Error Message 90
- Command information in 94
- 5.1.3 Warning Message 95
- TROUBLESHOOTING TABLE 96
- PARALLEL INTERFACE 98
- RS232 SERIAL INTERFACE 98
- LAN ETHERNET INTERFACE 99
- WIRELESS LAN INTERFACE 99
- Section 5: Troubleshooting 100
- BASIC SPECIFICATIONS 101
- PROCESSING 102
- PRINTER LANGUAGE 102
- CHARACTER FONT CAPABILITIES 103
- HARDWARE AND RELATED 106
- REGULATORY COMPLIANCE 106
- VERSATILE FUNCTIONS 106
- INTERFACE SPECIFICATIONS 111
- 7.2.2 Basic Specifications 113
- 7.2.3 Ready/Busy 114
- 7.2.4 X-ON/X-OFF 115
- 7.3.1 Basic Specifications 116
- 7.3.2 Pin Assignments 117
- TG3 Series Operator Manual 118
- 7.4.1 Basic Specifications 119
- 7.4.2 Pin Assignments 119
- 7.5.1 Basic Specifications 120
- 7.6 WIRELESS LAN ETHERNET 122
- <Important> 123
- 7.7.5 TELNET Specifications 126
- 7.7.6 Setting/Displayed Items 127
- 7.7.7 Wireless LAN Setting 128
- 7.8.1 Basic Specifications 129
- 7.8.2 Pin Assignments 129
- Page 7-20 130
- APPENDIX 131
- 8.1.1 Parts of Stacker Unit 132
- 8.1.2 To install the Stacker 133
- Metal clamp 134
- First spindle 134
- Section 8: Appendix 135
- Page 8-5 135
- 8.5 BASE REFERENCE POINT 136
- +/-99dot for each media 137
- Item Default value 139
- With cutting motion 141
- 8.7 JUMP HOLE 142
- 8.8 TAG SORTING METHOD 143
- 8.8.2 Separator 144
- Important: 144
- 8.9 PAPER END 145
- Masking 146
- 8.10 RIBBON END 147
- 8.11 RIBBON NEAR END 147
- 8.12 MEDIA SIZE CHECK 147
- 8.13 PERFORATED LINE 148
- Cut prohibited zone 149
- (1mm, 0.04”) 149
- Perforated line 149
- Page 8-20 150
- Page 9-1 151
- SATO GROUP OF COMPANIES 152
Related products and manuals for Label printers SATO TG312
Label printers SATO M-84PRO Specifications
(82 pages)
(82 pages)
Label printers SATO RFID User Manual
(26 pages)
(26 pages)
Label printers SATO CL608VA Specifications
(212 pages)
(212 pages)
(86 pages)
Label printers SATO CG208 Instruction Manual
(110 pages)
(110 pages)
Label printers SATO M60 User Manual
(5 pages)
© 2020, manymanuals.com. All rights reserved. | 1.730 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals