SATO TG312 Instruction Manual download pdf (Page 17)

Section 2: Installation

TG3 Series Operator Manual Page 2-3

2.2 MEDIA SELECTION (cont’d)

This printer accepts two types of media core sizes, φ 75mm (2.95”) and φ100mm (4”). When using φ100mm

(4“)

core size media, the supplied bosses need to be installed to the printer.

2.3 LOADING MEDIA

1. Lift up the main cover.

Note:

Make sure that the cover rests firmly so that it will not fall

forward and injure your hands.

2. Remove the roll media guide by pressing the release

tab with your thumb and index finger and pulling it out.

F75mm (2.95”)

F100mm (4”)

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 151 152

Operator Manual 1
Safety Precautions 3
Select a Safe Location 5
Power Supply 5
TABLE OF CONTENTS 6
Troubleshooting 5 - 1 7
Basic Specifications 6 - 1 7
Appendix 8 - 1 8
Sato Group of Companies 9 - 1 8
INTRODUCTION 9
1.1 FEATURES OF THE PRINTER 10
1.2 UNPACKING 10
1.3 PARTS IDENTIFICATION 11
Back view 12
INSTALLATION 15
2.1 SITE LOCATION 16
2.2 MEDIA SELECTION 16
2.3 LOADING MEDIA 17
2.3 LOADING MEDIA (cont’d) 18
2.4 MEDIA TYPE SELECTION 20
2.5 CUTTER SENSOR ADJUSTMENT 21
2.6 LOADING THE CARBON RIBBON 22
2.7 REMOVE THE CARBON RIBBON 24
2.8 BASIC CONNECTIONS 25
terminal on 27
2.9 LCD POWER SAVING MODE 29
Section 2: Installation 30
OPERATION AND CONFIGURATION 31
FUNCTION 32
3.1 OPERATOR PANEL (Cont’d) 33
3.2 OPERATING MODES 35
3.2 OPERATING MODES (Cont’d) 36
3.3 ONLINE AND OFFLINE MODES 38
Offline mode 40
3.6 USER MODE 42
3.6 USER MODE (Cont’d) 43
3.7 INTERFACE MODE 44
3.7 INTERFACE MODE (Cont’d) 45
3.8 SEMBL MODE 54
3.9 ADVANCED MODE 55
3.9 ADVANCED MODE (Cont’d) 56
3.10 HEX DUMP MODE 60
3.11 RFID USER MODE 61
3.11 RFID USER MODE (Cont’d) 62
3.12 TEST PRINT MODE 65
3.12 TEST PRINT MODE (Cont’d) 66
3.13 DEFAULT SETTING MODE 68
Default value 69
TG308 TG312 69
Service Mode 71
RFID Mode 71
3.15 SERVICE MODE 72
3.15 SERVICE MODE (Cont’d) 73
3.16 RFID MODE 80
3.16 RFID MODE (Cont’d) 81
Indication of 82
Deletion 82
3.17 DOWNLOAD MODE (Cont’d) 83
CLEANING AND MAINTENANCE 85
Cleaning sheet 87
4.4 ADJUSTING PRINT QUALITY 88
TROUBLESHOOTING 89
5.1.1 Error Message 90
Command information in 94
5.1.3 Warning Message 95
TROUBLESHOOTING TABLE 96
PARALLEL INTERFACE 98
RS232 SERIAL INTERFACE 98
LAN ETHERNET INTERFACE 99
WIRELESS LAN INTERFACE 99
Section 5: Troubleshooting 100
BASIC SPECIFICATIONS 101
PROCESSING 102
PRINTER LANGUAGE 102
CHARACTER FONT CAPABILITIES 103
HARDWARE AND RELATED 106
REGULATORY COMPLIANCE 106
VERSATILE FUNCTIONS 106
INTERFACE SPECIFICATIONS 111
7.2.2 Basic Specifications 113
7.2.3 Ready/Busy 114
7.2.4 X-ON/X-OFF 115
7.3.1 Basic Specifications 116
7.3.2 Pin Assignments 117
TG3 Series Operator Manual 118
7.4.1 Basic Specifications 119
7.4.2 Pin Assignments 119
7.5.1 Basic Specifications 120
7.6 WIRELESS LAN ETHERNET 122
<Important> 123
7.7.5 TELNET Specifications 126
7.7.6 Setting/Displayed Items 127
7.7.7 Wireless LAN Setting 128
7.8.1 Basic Specifications 129
7.8.2 Pin Assignments 129
Page 7-20 130
APPENDIX 131
8.1.1 Parts of Stacker Unit 132
8.1.2 To install the Stacker 133
Metal clamp 134
First spindle 134
Section 8: Appendix 135
Page 8-5 135
8.5 BASE REFERENCE POINT 136
+/-99dot for each media 137
Item Default value 139
With cutting motion 141
8.7 JUMP HOLE 142
8.8 TAG SORTING METHOD 143
8.8.2 Separator 144
Important: 144
8.9 PAPER END 145
Masking 146
8.10 RIBBON END 147
8.11 RIBBON NEAR END 147
8.12 MEDIA SIZE CHECK 147
8.13 PERFORATED LINE 148
Cut prohibited zone 149
(1mm, 0.04”) 149
Perforated line 149
Page 8-20 150
Page 9-1 151
SATO GROUP OF COMPANIES 152

Comments to this Manuals

No comments

SATO TG312 Instruction Manual Page 17

Comments to this Manuals

Related products and manuals for Label printers SATO TG312