SATO M8485S Operator's Manual Page 226
- Page / 228
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
RESET
If the custom Protocol Command codes are incorrect or if the printer does not
respond to commands using the custom set, the Alternate Protocol Control Codes can
be restored by the following procedure:
1. Turn the printer off.
2. Place DIP switch DS2-7 in the ON position.
3. Turn power on while simultaneously pressing the FEED and LINE switches.
4. When the message “ALT PROTOCOL DEFAULT COMPLETED” appears on the
display, turn the printer off.
5. When the printer is powered up again, the Alternate Protocol Command Code set
will be active. All previous custom settings will be lost.
DOWNLOAD PROCEDURE
The procedure for downloading a custom Protocol Command Code set is:
1. Reset the printer to the default settings using the Reset procedure.
2. Place DIP switch DS2-7 in the ON position.
3. Turn the POWER switch ON while simultaneously pressing the LINE switch. This
places the printer in the USER DOWNLOAD mode.
4. Set DIP switch DS2-7 in the position to accept the Protocol Control codes to be
used for downloading (i.e. DS2-7 = OFF for Standard codes and DS2-7 ON to use
the Alternate set).
5. Press the LINE key to place the M-8485S in the ON-LINE mode. The LINE LED
should be on and the printer is ready to receive the download command data
stream.
6. After the command has been sent, the unit will beep and print a status label. If it
does not beep and print the label, the printer did not accept the data.
7. If the printer does not beep and print a setting label, turn the printer off, check your
download command stream for errors and start the download process over at
step 1.
ALT PROTOCOL
DEFAULT COMPLETE
USER DOWNLOAD
Appendix E: Custom Protocol Command Codes
Page E-2 9001034 Rev E SATO “S” Print Engines
- “S” Applicator 1
- Print Engines 1
- Operator and Technical 1
- Reference Manual 1
- M-8485S OPERATOR’S MANUAL 3
- TABLE OF CONTENTS 5
- SECTION 1 9
- PRINTER OVERVIEW 9
- SPECIFICATIONS 10
- Inside Panel 11
- Section 1. Printer Overview 12
- SECTION 2 17
- INSTALLATION 17
- DIMENSIONS 18
- COMPONENT NAMES 19
- M-8459S Only 19
- M-8460S/M-8485S/M-8490S 19
- REAR PANEL 20
- SWITCHES AND SENSORS 21
- MEDIA LOADING 22
- Section 2. Installation 24
- ADJUSTING THE LABEL SENSOR 25
- OPERATION PANEL 27
- Operation Panel 27
- DIP SWITCH PANEL 28
- SECTION 3 29
- CONFIGURATION 29
- SATO DEFAULT 33
- COMPLETED 33
- POWER ON 34
- Receive Buffer 34
- Hex Dump Label 34
- Print Buffer 34
- PRINT SPEED 36
- PITCH OFFSET 36
- CANCEL PRINT 37
- ZERO SLASH 38
- AUTO ONLINE 38
- VERT. OFFSET 39
- HOR. OFFSET 39
- Label Feed Direction 40
- GAP (X.XV) 41
- INPUT (X 41
- Label Only Eye Mark 42
- Less than 1.0V 2.5V to 3.5V 42
- CALENDAR ENABLED 43
- 01/01/01 01:01 43
- USER TEST PRINT 46
- LARGE SMALL 46
- PRINT SIZE 46
- POTENTIOMETER ADJUSTMENTS 47
- HEX DUMP DIAGNOSTIC LABELS 49
- Print Buffer Hex Label 50
- Receive Buffer Hex Label 50
- SECTION 4 51
- CLEANING AND MAINTENANCE 51
- Paper End Switch 54
- Upper Sensor 54
- Sensor Window 54
- Ribbon Guide Roller 54
- REPLACING THE PRINT HEAD 55
- REPLACING THE FUSE 56
- SECTION 5. PROGRAMMING 57
- USING BASIC 58
- THE PRINT AREA 60
- SATOSATO 63
- COMMAND DEFAULT SETTINGS 64
- OPPOSITE HAND MODELS 65
- M-8485S Left-Hand 65
- COMMAND CODE PAGE REFERENCE 66
- Bar Codes 67
- Input to Printer 68
- UCC-128 Without Incrementing 70
- With Incrementing 70
- Bar Codes, Expansion 72
- Bar Codes, Variable Ratio 73
- Base Reference Point 75
- Characters, Custom-Designed 77
- Character Expansion 79
- Character, Fixed Spacing 81
- Character Pitch 82
- <ESC>* 85
- Continuous Forms Printing 86
- Copy Image Area 87
- Font, Vector 91
- Fonts WB, WL, XB & XL 93
- Form Feed 95
- Form Overlay, Recall 96
- Form Overlay, Store 97
- Graphics, Custom 98
- Graphics, PCX 100
- Job ID Store 101
- Journal Print 102
- Lines and Boxes 103
- Printer Output 104
- Line Feed 105
- Off-Line/Pause 106
- Print Darkness 108
- Print Length, Expanded 109
- Print Position 111
- Print Quantity 113
- Print Speed 114
- Repeat Label 115
- Replace Data (Partial Edit) 116
- Reverse Image 118
- Sequential Numbering 124
- <ESC>A 125
- <ESC>Q50 125
- <ESC>Z 125
- Start/Stop Label 126
- Calendar Option Commands 127
- Calendar Increment 128
- Calendar Print 130
- Calendar Set 132
- Memory Card Option Commands 133
- Memory Card Function 134
- Clear Card Memory 134
- Expand Memory Area 135
- Fonts, TrueType Recall 137
- Fonts, TrueType Store 138
- Format/Field Recall 139
- Format/Field Store 140
- Graphics, Custom Recall 141
- Graphics, Custom Store 142
- Graphics, PCX Recall 144
- Graphics, PCX Store 145
- Initialize 146
- Slot Select 147
- Custom Protocol Command Codes 149
- Download 149
- Two-Dimensional Symbols 151
- Two-Dimensional Bar Codes 152
- Data Matrix, Data Format 152
- Data Matrix, Print Data 154
- Maxicode 157
- SECTION 6 161
- INTERFACE SPECIFICATIONS 161
- RS232C SERIAL INTERFACE 163
- RS232C Interface Signals 164
- CENTRONICS PARALLEL INTERFACE 169
- EXT CONNECTOR 170
- SECTION 7 173
- TROUBLESHOOTING 173
- ERROR SIGNALS 176
- APPENDIX A 177
- COMMAND CODE QUICK REFERENCE 177
- APPENDIX B 189
- BAR CODE SPECIFICATIONS 189
- <ESC>BD0bbcccd (data) d 190
- UPC-A/EAN-13 193
- ODD 024680 194
- EVEN 13579CD 194
- Industrial Two of Five 196
- Matrix Two of Five 197
- Code 128 198
- Example Without incrementing 204
- With incrementing 204
- Data Matrix 206
- Character Set 207
- CODE 128 CHARACTER TABLE 210
- Code 128 Character Table 211
- APPENDIX C 213
- CUSTOM GRAPHICS EXAMPLE 216
- PCX GRAPHICS EXAMPLE 220
- APPENDIX D 221
- OPTIONAL ACCESSORIES 221
- CALENDAR 222
- TOP MOUNTED REFLECTIVE SENSOR 223
- Appendix D: Optional Features 224
- APPENDIX E 225
- CUSTOM PROTOCOL COMMAND CODES 225
- USER DOWNLOAD 226
- ALT PROTOCOL 226
- DEFAULT COMPLETE 226
Related products and manuals for Label printers SATO M8485S
Label printers SATO CG212DT Instruction Manual
(109 pages)
(109 pages)
Label printers SATO M-5900 Service Manual
(66 pages)
(66 pages)
Label printers SATO /gt Series Service Manual
(106 pages)
(106 pages)
Label printers SATO CL608 Service Manual
(245 pages)
(245 pages)
Label printers SATO CG412 Specifications
(100 pages)
(100 pages)
Label printers SATO CL608 Specifications
(58 pages)
(58 pages)
Label printers SATO M-84PRO Specifications
(52 pages)
(52 pages)
Label printers SATO CL408e Specifications
(10 pages)
(10 pages)
Label printers SATO LM408e Specifications
(86 pages)
(86 pages)
Label printers SATO LM408-LM412e Service Manual
(130 pages)
(130 pages)
Label printers SATO TH2 User Manual
(15 pages)
(15 pages)
Label printers SATO M-8400 Operator's Manual
(242 pages)
(242 pages)
Label printers SATO M8485S Operator's Manual
(107 pages)
(107 pages)
(87 pages)
Label printers SATO M-10E Specifications
(82 pages)
(82 pages)
Label printers SATO TG312 Instruction Manual
(152 pages)
(152 pages)
© 2020, manymanuals.com. All rights reserved. | 4.510 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals